Mechanical properties of frictional welded joints: a review
Article Sidebar
Main Article Content
Abstract
Friction welding is an effective process for joining similar and dissimilar materials. It is widely used in industrial applications for automobiles and aircraft. It can be used to produce high-quality joints, so it is considered an alternative to traditional joining methods. As a result of friction between the two workpieces, sufficient heat is generated to soften the interface without reaching the melting point, which allows materials with different physical properties to be bonded. Process parameters such as speed, friction pressure, friction time, forging pressure and forging time have a major influence on the mechanical properties of the joint. One of these important properties is tensile strength. In this review, published research papers by various researchers were studied and the influence of parameters on the mechanical properties of welded joints was discussed.
Article Details
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Licensed under a CC-BY license: https://creativecommons.org/licenses/by-nc-sa/4.0/
How to Cite
References
M. Maalekian, “Friction welding – critical assessment of literature,” Sci. Technol. Weld. Join., vol. 12, pp. 738–759, 2007, [Online]. Available:https://api.semanticscholar.org/CorpusID:136934570
M. Haghshenas and A. P. Gerlich, “Joining of automotive sheet materials by friction-based welding methods: A review,” Eng. Sci. Technol. an Int. J., vol. 21, pp. 130–148, 2018, [Online]. Available: https://api.semanticscholar.org/CorpusID:139539316.
V. Ajay, N. K. Babu, M. Ashfaq, T. M. Kumar, and K. V. Krishna, “A Review on Rotary and Linear Friction Welding of Inconel Alloys,” Trans. Indian Inst. Met., vol. 74, no. 11, pp. 2583–2598, 2021, doi: 10.1007/s12666-021-02345-z.
H. D. Vyas, K. P. Mehta, V. Badheka, and B. Doshi, “Friction welding of dissimilar joints copper-stainless steel pipe consist of 0.06 wall thickness to pipe diameter ratio,” J. Manuf. Process., vol. 68, pp. 1176–1190, 2021, doi: https://doi.org/10.1016/j.jmapro.2021.06.050.
M. Sahin, “Evaluation of the joint-interface properties of austenitic-stainless steels (AISI 304) joined by friction welding,” Mater. & Des., vol. 28, pp. 2244–2250, 2007, [Online]. Available:https://api.semanticscholar.org/CorpusID:137326809.
M.-N. Avettand-Fènoël, G. Racineux, L. Debeugny, and R. Taillard, “Microstructural characterization and mechanical performance of an AA2024 aluminium alloy - Pure copper joint obtained by linear friction welding,” Mater. & Des., vol. 98, pp. 305–318, 2016, [Online]. Available:https://api.semanticscholar.org/CorpusID:138926967
K. Ozel, M. Sahin, and A. Akdogan, “Mechanical and Metallurgical Properties of Aluminium and Copper Sheets Joined by Cold Pressure Welding,” Strojni{vs}ki Vestn., vol. 54, pp. 796–806, 2008, [Online]. Available: https://api.semanticscholar.org/CorpusID:138816790
H. Nami, H. Adgi, M. Sharifitabar, and H. E. Shamabadi, “Microstructure and mechanical properties of friction stir welded Al/Mg 2Si metal matrix cast composite,” Mater. & Des., 2011, [Online]. Available: https://api.semanticscholar.org/CorpusID:135769431
D. Wang, Q. Z. Wang, B. L. Xiao, and Z. Y. Ma, “Achieving friction stir welded SiCp/Al-Cu-Mg composite joint of nearly equal strength to base material at high welding speed,” Mater. Sci. Eng. A-structural Mater. Prop. Microstruct. Process., vol. 589, pp. 271–274, 2014, [Online].Available:https://api.semanticscholar.org/CorpusID:137526037
D. L. Olson and J. R. Davis, “Welding, brazing, and soldering,” 1993. [Online]. Available: https://api.semanticscholar.org/CorpusID:85504603
M. B. Uday, M. N. A. Fauzi, H. Zuhailawati, and A. B. Ismail, “Advances in friction welding process: A review,” Sci. Technol. Weld. Join., vol. 15, pp. 534–558, 2010, [Online]. Available: https://api.semanticscholar.org/CorpusID:137289085
E. P. Alves, F. P. Neto, and C. Y. An, “Welding of AA1050 aluminum with AISI 304 stainless steel by rotary friction welding process,” J. Aerosp. Technol. Manag., vol. 2, pp. 301–306, 2010, [Online]. Available: https://api.semanticscholar.org/CorpusID:59128302
“Rotary Friction Welding of Dissimilar Materials,” Int. J. Recent Technol. Eng., 2019, [Online]. Available: https://api.semanticscholar.org/CorpusID:242539777
R. Winiczenko, A. Skibicki, and P. Skoczylas, “Optimization of Friction Welding Parameters to Maximize the Tensile Strength of Magnesium Alloy with Aluminum Alloy Dissimilar Joints Using Genetic Algorithm,” Processes, 2021, [Online]. Available: https://api.semanticscholar.org/CorpusID:239675241
R. Paventhan, P. R. Lakshminarayanan, and V. Balasubramanian, “Optimization of Friction Welding Process Parameters for Joining Carbon Steel and Stainless Steel,” J. Iron Steel Res. Int., vol. 19, no. 1, pp. 66–71, 2012, doi: 10.1016/S1006-706X(12)60049-1.
R. Winiczenko and M. Kaczorowski, “Friction welding of ductile iron with stainless steel,” J. Mater. Process. Technol., vol. 213, pp. 453–462, 2013, [Online]. Available: https://api.semanticscholar.org/CorpusID:137216854
S. T. Selvamani and K. Palanikumar, “Optimizing the friction welding parameters to attain maximum tensile strength in AISI 1035 grade carbon steel rods,” Measurement, vol. 53, pp. 10–21, 2014, [Online]. Available: https://api.semanticscholar.org/CorpusID:110518503
T. N. Prasanthi, C. Sudha, Ravikirana, S. Saroja, N. Kumar, and G. D. Janakiram, “Friction welding of mild steel and titanium: Optimization of process parameters and evolution of interface microstructure,” Mater. & Des., vol. 88, pp. 58–68, 2015, [Online]. Available: https://api.semanticscholar.org/CorpusID:136960040
M. Kimura, T. Iijima, M. Kusaka, K. Kaizu, and A. Fuji, “Joining phenomena and tensile strength of friction welded joint between Ti–6Al–4V titanium alloy and low carbon steel,” J. Manuf. Process., vol. 24, pp. 203–211, 2016, [Online]. Available: https://api.semanticscholar.org/CorpusID:138559111
A. C. Reddy, “Evaluation of Parametric Significance in Friction Welding Process of AA1100 and Zr705 Alloy using Finite Element Analysis,” Mater. Today Proc., vol. 4, pp. 2624–2631, 2017, [Online]. Available: https://api.semanticscholar.org/CorpusID:136158742
A. R. McAndrew, P. A. Colegrove, C. Bühr, B. C. D. Flipo, and A. Vairis, “A literature review of Ti-6Al-4V linear friction welding,” Prog. Mater. Sci., vol. 92, pp. 225–257, 2018.
X. Wang, W. Li, T. Ma, X. Yang, and A. Vairis, “Effect of welding parameters on the microstructure and mechanical properties of linear friction welded Ti-6.5Al-3.5Mo-1.5Zr-0.3Si joints,” J. Manuf. Process., 2019, [Online]. Available: https://api.semanticscholar.org/CorpusID:202944872
M. Cheepu and W. S. Che, “Effect of Burn-off Length on the Properties of Friction Welded Dissimilar Steel Bars,” J. Weld. Join., 2019, [Online]. Available: https://api.semanticscholar.org/CorpusID:139492039
M. Kimura, K. Ohara, M. Kusaka, K. Kaizu, and K. Hayashida, “Effects of tensile strength on friction welding condition and weld faying surface properties of friction welded joints between pure copper and austenitic stainless steel,” 2020. [Online]. Available: https://api.semanticscholar.org/CorpusID:225607666
M. D. Kumar and P. K. Palani, “Characterization studies on weld strength of rotary friction welded austenitic stainless steel tubes,” Mater. Today Proc., 2020, [Online]. Available: https://api.semanticscholar.org/CorpusID:225467534
J. A. Anandaraj, S. Rajakumar, V. Balasubramanian, and V. Petley, “Investigation on mechanical and metallurgical properties of rotary friction welded In718/SS410 dissimilar materials,” Mater. Today Proc., 2020, [Online]. Available: https://api.semanticscholar.org/CorpusID:216401471
M. Xie, X. Shang, Y. Li, Z. Zhang, M. Zhu, and J. Xiong, “Rotary Friction Welding of Molybdenum without Upset Forging.,” Mater. (Basel, Switzerland), vol. 13, no. 8, Apr. 2020, doi: 10.3390/ma13081957.
M. Balasubramanian, S. Murali, C. Hemadri, and R. Kumar, “A new method of dissimilar friction welding of titanium to stainless steel,” Mater. Today Proc., 2021, [Online]. Available: https://api.semanticscholar.org/CorpusID:233973816
A. Banerjee, M. Ntovas, L. da Silva, and S. Rahimi, “Microstructure and mechanical properties of dissimilar inertia friction welded 316L stainless steel to A516 ferritic steel for potential applications in nuclear reactors,” Manuf. Lett., 2022, [Online]. Available: https://api.semanticscholar.org/CorpusID:250516592
S. Sundaraselvan, N. Senthilkumar, T. Balamurugan, C. Kaviarasu, G. B. Sathishkumar, and M. N. Rajesh, “Optimization of friction welding process parameters for Joining Al6082 and mild steel using RSM,” Mater. Today Proc., 2022, [Online]. Available: https://api.semanticscholar.org/CorpusID:254670170
S. Raj and P. Biswas, “Effect of Induction Preheating on Microstructure and Mechanical Properties of Friction Stir Welded Dissimilar Material Joints of Inconel 718 and Ss316l,” SSRN Electron. J., 2023, [Online]. Available: https://api.semanticscholar.org/CorpusID:251111945